Home › Blog › Multi-room Viewing

No Communication From Primary Decoder: How to Fix It

Multi-room ViewingBy our Rondebosch DStv teamUpdated 28 October 20267 min read

First fix: go to the main decoder, check it's on and showing a picture, then switch the second box off and on again. That alone clears no communication from primary decoder in a lot of Rondebosch homes. If it doesn't, the four fixes below cover power, restart order, cables and your account.

Quick answer

To fix no communication from the primary decoder, make sure the main XtraView box is powered on with a picture. Switch both boxes off, start the main one first, then the second one. Press the cable connectors snug at the back and confirm your account is paid and linked. Repeat faults point to the link cable.

Fix 1: no communication from the primary decoder? Wake it up

The second decoder in XtraView can't work alone. It depends on a steady check-in signal from the main box, which DStv calls the heartbeat. If the main decoder is off, unplugged or frozen, the second TV blanks out.

  • Look for lights on the front of the main decoder.
  • Switch on its TV and check for a normal picture.
  • If the screen is frozen, switch it off at the plug and on again.

In shared student digs near UCT, this is the cause more often than anything else. A housemate unplugs the lounge box to charge a laptop, and the room down the passage loses its TV. Our post on DStv in flats and student digs has more house-share tips.

Fix 2: restart in the right order

After a power cut, both boxes come back together. The second one can finish booting before the main box is ready, give up on the link and show the error. Here's the order that works.

  1. Switch off both decoders at the wall.
  2. Count to sixty.
  3. Power up the main decoder and wait for a normal picture.
  4. Power up the second decoder and give it a few minutes.

If the main box itself won't start, our post on common DStv error codes may point you to the cause.

Fix 3: check cables when there's no communication from the primary decoder

The heartbeat travels along the coax cable that links the boxes. DStv's page on primary and secondary decoder roles notes that interference or cabling errors can interrupt it, even with both boxes switched on.

Reach behind each decoder and gently press the round screw-on connectors so they're snug. Don't unscrew or swap them around, because putting a cable in the wrong socket can cause new faults. Look for kinks where a cable is squashed behind a cupboard.

Safety first

Leave the roof, the dish and anything behind the walls alone. Don't use a ladder to trace cables in high Victorian ceilings, and never open a decoder. Hand checks at the back of the boxes are as far as a DIY fix should go.

Fix 4: confirm the account side

Sometimes the wiring is perfect and the problem is billing. XtraView must be linked on your DStv account, and both decoders must be on the same package. An unpaid account can also stop both boxes.

Open the MyDStv app or log in on dstv.com to check that your payment is up to date and both smartcards appear under XtraView. If something looks wrong, re-authorise the decoders from the app.

Need DStv installers in Rondebosch?

Tell us what you need or what your screen is showing. We give you a clear price before we drive out.

Which fix matches your symptom

What happened before the errorMost likely fixTime needed
Someone unplugged things or moved furnitureFix 1 or Fix 3About 2 minutes
Power cut or load reductionFix 2About 5 minutes
Rainy week, error comes and goesCable test by a technicianOne visit
New setup, never worked properlyFix 4, then a link checkVaries
Main TV shows E48-32 tooDish signal, not XtraViewOne visit

That last row matters. If the main TV has no signal, the link isn't the problem, and our post on E48-32 after rain is the better read.

Old houses, flats and long cable runs in Rondebosch

Many Rondebosch homes are Victorian or Edwardian, with thick walls and long passages. The cable between the lounge and a back bedroom can run through ceilings, under floors and past old wiring. Each join is a place where damp from our wet winters can creep in.

Blocks of flats in Mowbray, Rosebank and Rondebosch East bring their own problems. Cables are often shared or rerouted during renovations. In those buildings our communal DStv systems work sometimes overlaps with an XtraView fault.

Leafy streets in Newlands and Claremont add another twist. Builders and tree fellers working near the house can knock or cut a cable without anyone noticing.

Still showing XtraView not working? Call a technician

If all four fixes fail, or the message keeps returning, the fault is likely in the cable, a connector, a splitter or a decoder port. Some people describe this as a DStv heartbeat error that won't go away. Testing it needs a meter.

Good to know

DStv suggests using an Explora as the main decoder in XtraView, so your recordings aren't affected when the link breaks. If you're choosing boxes again, read how XtraView works first.

When we come out for XtraView setup and repairs, we test the full cable run, replace tired connectors and check both decoders on your account. If a box is faulty, our DStv repairs team can help with that too.

Book help when there's still no communication from your primary decoder

If these steps don't solve it, please call a technician before buying new hardware. We're local DStv installers in Rondebosch and the southern suburbs, and we always quote before we drive out. Get in touch through our contact page or call 072 237 6363.

No communication from primary decoder: FAQs

How do I fix no communication from primary decoder?

Switch both boxes off at the wall, start the main decoder first and wait for a picture, then switch on the second one. Press the cable connectors snug and check your account is paid. If it keeps coming back, have the link cable tested.

What is error E143 on DStv?

It's the code some decoders show alongside the waiting or no communication message in XtraView. It means the second decoder isn't receiving the signal from the main box. The same restart and cable checks apply.

Why does my second decoder say no communication from the primary decoder after a power cut?

Both boxes restart together and the second one may finish first, so it can't find the main box. Switch both off, start the main decoder, wait for a picture and then power up the second decoder.

Can a technician come out for an XtraView fault in Rondebosch?

Yes. We cover Rondebosch and nearby suburbs like Newlands, Claremont and Observatory. We test the link cable and connectors, check both decoders and give you a quote before we drive out.

How do I check XtraView settings?

Use the MyDStv app or your account on dstv.com to see that both smartcards are linked under XtraView and on the same package. On the decoders themselves, check both are on and connected before changing any settings.

Talk to our Rondebosch team

Call or WhatsApp us for a quote. We answer quickly and we always price the job before we arrive.